It is important to point Syslinux to the correct root partition by editing /boot/syslinux/syslinux.cfg, or the OS will fail to boot. Warning: The syslinux-install_update script sets a default root partition that possibly will not match your particular system. The lib*.c32 library modules and non-core *.c32 modules should match the version of ldlinux.sys installed in the partition. This step and the rest of non-core parts of Syslinux ( /boot/syslinux/*.c32 modules, excluding lib*.c32 and ldlinux.c32) require /boot/syslinux/lib*.c32 (library) modules to be present ( ). If no configuration file is found, you will be dropped to a Syslinux boot: prompt. Stage 4 - Search and Load configuration file Once Syslinux is fully loaded, it looks for /boot/syslinux/syslinux.cfg (or /boot/syslinux/nf in some cases) and loads it if it is found. The ldlinux.c32 file should be present in every Syslinux installation and should match the version of ldlinux.sys installed in the partition. Stage 3 - Load /boot/syslinux/ldlinux.c32 The /boot/syslinux/ldlinux.sys will load the /boot/syslinux/ldlinux.c32 (core module) that contains the rest of the core part of syslinux that could not be fit into ldlinux.sys (due to file-size constraints). ![]() Therefore, in Btrfs the entire ldlinux.sys code is embedded in the space following the VBR and is not installed at /boot/syslinux/ldlinux.sys unlike the case of other filesystems. Note: In the case of Btrfs, the above method will not work since files move around resulting in changing of the sector location of ldlinux.sys. ![]() The sector location of /boot/syslinux/ldlinux.sys should not change, otherwise syslinux will not boot. Stage 2 - Part 2 - Execute /boot/syslinux/ldlinux.sys The VBR will load the rest of /boot/syslinux/ldlinux.sys. Note that ldlinux.sys is not the same as ldlinux.c32. In the case of Syslinux, the VBR boot code is the starting sector of /boot/syslinux/ldlinux.sys which is created by the extlinux -install command. Stage 2 - Part 1 - Execute volume boot record The Stage 1 MBR boot code executes the Volume Boot Record (VBR) of the /boot partition. Let us assume this is the /boot partition, for example. Stage 1 - Part 2 - Search active partition The Stage 1 MBR boot code looks for the partition that is marked as active (boot flag in MBR disks). Stage 1 - Part 1 - Load MBR At boot, the BIOS loads the 440 byte MBR boot code at the start of the disk ( /usr/lib/syslinux/bios/mbr.bin or /usr/lib/syslinux/bios/gptmbr.bin). Syslinux boot process on BIOS happens in stages: After installing the relevant package(s), the bootloader code itself needs to be installed (to the adequate area, usually the VBR or ESP) so to be able to boot the system the following sections provide alternative instructions depending on the characteristics of your particular system. Installing the package is not the same as installing the bootloader. UEFI booting requires installing the efibootmgr package. InstallationīIOS booting will also require the gptfdisk package for BIOS/GPT setups and mtools if your /boot partition is FAT-formatted. ![]() See #Chainloading on how to work around this. You can then create a new partition and format it FAT32 and it will work.Note: Syslinux, by itself, cannot access files from partitions other than its own. The solution is to remove the partition table on the device, and remake a new partition table. Perhaps it's not marked bootable, or has something non-standard in there. The problem is the partition table that the manufacturers put on the devices. Ok, I've just verified this problem with Unetbootin and Ubuntu Startup disk creator on a Verbatim 2Gb drive. I think it's important enough to put it here in clear as it's caused a problem for quite a few people, myself included: I'm adding this as another edit, because my comment below seems to get hidden by a "show more" link. The solution is to delete the partition table completely, remake it, and re-format FAT. ![]() after I reformatted it to ntfs it didn't have the error I have come across situations where the partition table put on the USB stick by the manufacturer causes some problems. This can save you a lot of grief later if it turns out the download was corruptĮdit: I think the LiveUSB must be formatted FAT to be able to boot off Chris Mine had fat32 but it didn't work. Download Unetbootin for Windows and try that:īefore going ahead and making the Bootable USB, it's always a good idea to check the md5sum of the iso that you downloaded:
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |